Enter the floor area affected by water, choose the closest contamination category, and select your metro. The range covers extraction and drying under the assumptions shown below. Ask the contractor to separate the cost of stopping the leak and rebuilding damaged finishes from the work needed to dry the structure.
RestoreRadar’s November 10, 2026 planning model starts at $4.50–$7.50 per affected square foot. Multiply each end by the damage factor and metro factor shown in the controls, then apply the minimums of $1,200 and $1,800. “Not sure” spans the lowest through highest damage factors.
The metro selector shows the exact multiplier used for each city. RestoreRadar supplied these scenario factors for 15 metros. Elsewhere we apply the unadjusted base rate (1.00×). The rates, minimums and multipliers are planning assumptions. We have no local contractor bid sample or restoration price index validating them.
National published cost context
Angi reports $450–$16,000 for U.S. projects (checked 2026-08-10).
This is not the model result above. Published project costs describe broader scopes and do not establish RestoreRadar’s square-foot rates or metro factors.
Compare water damage scenarios
Examples with a square footage use RestoreRadar’s planning model at the base metro factor (1.00×). The affected areas are illustrative. The national project figures from Angi provide context. See the model rates and minimums for the calculation.
Example scopes and planning ranges
Situation
Assumed scope
Planning range
What to ask about
Clean burst supply pipe
250 sq ft · 1× damage factor
$1,200 – $1,875
Extraction and drying after the supply is shut off. Price plumbing repairs separately.
Gray water appliance leak
250 sq ft · 1.45× damage factor
$1,631 – $2,719
Assumes used appliance water reached the floor. Confirm which materials need removal.
Category 3 sewage backup
250 sq ft · 2.1× damage factor
$2,363 – $3,938
Ask for a written scope for contaminated material removal, disposal and cleaning.
Use This Water Damage Range in a Written Estimate
Use the result to compare like-for-like water-loss scopes, not to pick a company by the lowest total. Ask each company to identify the water source and affected materials, show initial moisture readings, list extraction and drying equipment, state how conditions will be monitored, and define the readings or material condition that will support completion. Separate plumbing or source repair, contaminated-material handling, structural drying, demolition, contents work, and reconstruction so omissions are visible. Photograph accessible damage before disposal when it is safe and keep equipment logs, estimates, change orders, and receipts. A sanitary supply-line leak, sewage backup, and outside floodwater do not call for identical precautions or material decisions. This calculator cannot observe contamination, concealed moisture, insulation, subfloors, cabinets, HVAC exposure, access, or local labor; those facts belong in the on-site written scope.
What a Water-Restoration Scope Should Make Visible
A useful scope identifies affected rooms and materials, initial and comparison readings, equipment and monitoring, drying criteria, removal reasons, and the written completion basis. The actual sequence depends on the water source, contamination, materials, and conditions found on site; a generic checklist cannot prescribe every step.
Keep Mitigation, Contamination Work, and Reconstruction Separate
Extraction, drying, dehumidification, and monitoring can limit additional water damage. Mold, sewage, floodwater, or other contaminated materials may require a different remediation scope, while restoration or reconstruction repairs the building afterward. One company may offer several phases, but the contract should state which phase is authorized, which regulated trades or permits are separate, and what the completion record covers. A contractor can document a loss and proposed scope; the insurer applies the policy and decides coverage. The NFIP/FloodSmart source below applies specifically to NFIP flood claims; other property coverage depends on the applicable policy.
Your contact details may be shared with up to three companies listed for the selected area. See which companies may receive your request. Sponsored or claimed companies may be contacted first. Paid placement never changes rankings or listing facts.
Questions
How is the water damage range calculated?
The model starts at $4.50–$7.50 per affected square foot. It adjusts both ends for the selected water category and metro, then applies minimum job amounts of $1,200 and $1,800.
What does the estimate include?
The three lines cover extraction and moisture mapping, drying equipment and labor, and antimicrobial treatment and material disposal. Ask your contractor to price leak repairs and reconstruction separately.
What do water damage categories 1, 2, and 3 mean?
They describe contamination after inspection, not a fixed timer. Category 1 begins at a sanitary source; Category 2 contains significant contamination; Category 3 is grossly contaminated and can contain harmful agents. Source, materials contacted, time, temperature, and observed conditions inform the preliminary determination, and weather-related water is not automatically Category 3. EPA's separate 24-to-48-hour guidance is a drying target to reduce mold growth, not an automatic category change. Avoid contact with sewage or floodwater and have the actual loss assessed.